Identifikasi risiko bahaya kerja dengan metode HIRADC di PT. Pelabuhan Tanjung Priok pada bagian maintenance mesin gantry lufting crane (GLC)
DOI:
https://doi.org/10.33019/2apd3955Keywords:
HIRADC, Hazard Identification, Occupational Risk Assessment, Occupational SafetyAbstract
All types of work certainly have a risk of danger with their respective levels including work in the maintenance section. From the above problems, the research aims to identify hazards, risk assessment, and risk control of hazards at PT Pelabuhan Tanjung Priok Banten Branch using the HIRADC method. This research uses qualitative methods with descriptive research types. The data in this study were taken from direct observation during the process of implementing industrial practice, which is one month. Then, the data was analysed using the HIRADC Method (Hazard Identification, Risk Assessment, and Determine Control). The results showed that there were five types of work observed including welding, combustion engine maintenance, cleaning the electrical room, lubrication, and preventive maintenance. The identification results show that the risk level varies from low to high, with the highest risk in work at height. Recommended control measures include the use of PPE, occupational safety training, implementation of lockout-tagout procedures, and installation of fall protection systems. The implementation of these controls is important to minimise work accidents and improve safety in the dock environment.
Downloads
References
[1] B. Ketenagakerjaan, “Jumlah Kasus Kecelakaan Kerja di Indonesia Menurut Provinsi dan Segmen Kepesertaan Bulan Mei Tahun 2023.” 2023.
[2] T. Saputro and D. Lombardo, “Metode Hazard Identification, Risk Assessment and Determining Control (HIRADC) Dalam Mengendalikan Risiko Di PT. Zae Elang Perkasa,” J. Baut Dan Manufaktur, vol. 03, no. 1, pp. 23–29, 2021.
[3] Y. Atiyah and E. K. Wibowo, “Penerapan Keselamatan dan Kesehatan Kerja Pada Pegawai Saat Pandemi Covid-19 di Rumah Sakit Jantung dan Pembuluh Darah Harapan Kita,” J. Sumber Daya Apar., pp. 61–81, 2023.
[4] T. Sukwika, “Analisis Manajemen Risiko Keselamatan dan Kesehatan Kerja Menggunakan Metode HIRADC pada Departemen Assembly Listrik,” J. Appl. Manag. Res., vol. 1, no. 2, pp. 119–127, 2021.
[5] A. Trisiana, S. A. Y. Dwi, and R. Anik, “Assessment Risiko Kesehatan dan Keselamatan Kerja (K3) Menurut Variabel OHSAS Dengan Menggunakan HAZOP (Hazard And Operability Study) dan HIRADC (Hazard Identification Risk Assement end Determining Control (Studi Kasus: Proyek Pembangunan Ciputra World Ph,” Pengaruh Ter. Psikoedukasi Kel. Terhadap Tingkat Kecemasan Kel. pada Anggota Kel. yang Menderita Katakan di Wil. Kerja Puskesmas Jelbuk Kabupaten Jember, vol. 3, pp. 28–37, 2019.
[6] M. I. Pasaribu, D. A. A. Ritonga, and A. Irwan, “Analisis Perawatan (Maintenance) Mesin Screw Press Di Pabrik Kelapa Sawit Dengan Metode Failure Mode and Effect Analysis (Fmea) Di Pt. Xyz,” Jitekh, vol. 9, no. 2, pp. 104–110, 2021, doi: 10.35447/jitekh.v9i2.432.
[7] S. Santoso, “Penerapan Metode Hiradc Sebagai Upaya Pencegahan Risiko Kecelakaan Kerja Pada Divisi Operasi Pembangkit Listrik Tenaga Gas Uap,” J. Bisnis Manaj., vol. 20, pp. 41–64, 2020.
[8] R. Safrudin, Zulfamanna, M. Kustati, and N. Sepriyanti, “Penelitian Kualitatif,” J. Soc. Sci. Res., vol. 3, no. 2, pp. 1–15, 2023.
[9] D. S. Urrohmah and D. Riandadari, “Identifikasi Bahaya dengan Metode HIRARC dalam Upaya Memperkecil Risiko Kecelakaan Kerja di PT . PAL Indonesia,” J. Tek. Mesin UNESA, vol. 08, no. 01, pp. 34–40, 2019.
[10] Restu and F. Yuamita, “Analisis Risiko Potensi Kecelakaan Kerja Pada Pekerja Departemen Persiapan Produksi Menggunakan Metode HIRADC (Hazard Identification, Risk Assesment And Determining Control),” J. Teknol. dan Manaj. Ind. Terap., vol. 2, no. 3, pp. 159–167, 2023, doi: 10.55826/tmit.v2i3.63.
[11] R. M. Zein, M. Jufriyanto, and Y. Pandu, “Manjemen Risiko Pada Proses Produksi Tanki Air: Metode Hazard Identification Risk Assessment Risk Control (HIRARC),” Gn. Malang, Randu Agung, Kec. Kebomas. Kab. Gresik, vol. 19, no. 2, p. 61121, 2022.
[12] T. Ihsan, S. A. Hamidi, and F. A. Putri, “Penilaian Risiko dengan Metode HIRADC Pada Pekerjaan Konstruksi Gedung Kebudayaan Sumatera Barat,” J. Civronlit Unbari, vol. 5, no. 2, p. 67, 2020, doi: 10.33087/civronlit.v5i2.67.
[13] Dea Artha Melati, Ekowati Retnaningtyas, and Diniyah Kholidah, “Analisis Tingkat Pengetahuan Keselamatan dan Kesehatan Kerja (K3) Mengenai Lockout/Tagout (LOTO) terhadap Tindakan Tidak Aman (Unsafe Action) dalam Lockout/Tagout (LOTO) Pekerja Divisi Manufactur dan Divisi Enggenering pada PT. X Kabupaten Banyuwangi,” Detect. J. Inov. Ris. Ilmu Kesehat., vol. 2, no. 3, pp. 99–108, 2024, doi: 10.55606/detector.v2i3.4149
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Machine : Jurnal Teknik Mesin
This work is licensed under a Creative Commons Attribution 4.0 International License.
The paper presented is assumed not to contain proprietary materials that are not protected by patents or patent applications. Responsibility for technical content and for protection from proprietary materials is the responsibility of the author and their organization and not the responsibility of the machine or its editorial staff. The primary author (first / appropriate) is responsible for ensuring that the article has been viewed and approved by all other authors. It is the responsibility of the author to obtain all copyright release permits required for the use of any copyrighted material in the manuscript before submission.
How to Cite
Share
